The Barking Dog Alarm Enhanced Setup Instructions
Setup of Barking Dog Alarm brands Safety Technology & Safe Family Life model EWD-1, HomeSafe model 639SR, or StreetWise model SWEWD is a simple process once you are familiar with the unit. Please study these instructions, as this Main Unit is very sensitive and may need to be adjusted and moved as little as a few inches to reach the desired first-time results.
We have provided setup instructions in two parts. In part one; we have included basic setup instructions and considerations for placement of the Main Unit. In part two; we have included the process to expand the basic alarm unit by adding Motion Sensors, Remote Controls, and Door/Window Vibration sensors. Please DO NOT move on to part two until part one is completed.
How To Setup The Main Unit:
To start the setup, you need to install 8 AA-size batteries so the unit can operate properly and supply backup in case of a power failure. Plugin the AC to 12 volt DC adaptor to the main unit DC power port (Fig.5).
Install the fresh included battery in the Remote Control.
The Main Unit should be placed 2.5 to 5 feet from the floor with the battery side facing the object you want to see through. The speaker side faces inside the room where the sound will fill the area and bounce off of the walls for a realistic sound from the outside. Fig A; B; C; and D show the right and wrong way to place the alarm around a door if it is made of metal. Notice that the alarm Main Unit is angled toward the outside of the door to improve the angle of detection.
The Main Unit can also be mounted on the wall 2.5 to about 6 feet from the floor and away from heat sources. Figures E and F show a wall mount with the broken lines showing a typical area of detection.
All of the Barking Dog Alarm Main Units mentioned in these instructions are identical with the exception of the brand name and model. They are designed to detect through wood; glass; brick; plastic; and other barriers. During setup, keep in mind that the Main Unit will NOT detect through metal and there may be reduced or no penetration through ultra-thick barriers; objects that contain rebar; metal window coatings; chicken wire, and any other metal that is hidden in the wall. If you have an issue, adding an outdoor adjustable motion sensor should get around the problem.
The Radar Wave/Microwave sensor is very sensitive and just like a real dog, when armed, it will activate at anything that it sees moving, including plant leaves; heavy rain; large insects; computer fans, and curtains. The sensor will see movement from all sides, however, only the Battery Side is designed to detect through objects. The other sides have a reduced range and may activate the unit when you get close to it.
When set to bark, the Main Unit will give warning barks if it sees motion. If the motion continues the barking will get more vicious until the main unit no longer sees movement. The main unit will work best if it can continuously see a person as they walk toward it. The main unit can also be set to chime or siren.
The Main Unit sensitivity control can be used to set the distance that the barking dog alarm will pick up movement. This maximum distance of this control depends on the object that the sensor is looking through. Keep in mind that the higher the sensitivity is set, the more movement it will see. You may also need to move the main unit if you are not getting the desired trigger. Even a few inches can make a difference.
The Main Unit off/on volume control is used to power on the unit and set the desired volume of the bark, siren, or chime; depending on which sound type setting you have chosen.
After selecting the location to place the Barking Dog Main Unit, you will want to test the range and loudness of the alarm. For first-time power-up of the main unit, it is recommended that the chime mode be used.
Turn on the power by turning the power/volume adjustment switch (fig.1). The Power/Battery low LED on the front of the Main Unit should glow green and the Arm LED may glow red indicating the alarm is armed.
*Note If you do not see the green LED, after you turn on your Main Unit, you are running on the batteries. Be sure the adapter is plugged into AC power and the Alarm Unit DC port. If the Arm LED is not glowing red, Either press the Arm/Disarm button on side of the Main Unit or press the arm button on the Remote Control. The ARM LED on the front of the Main Unit will light up.
In Bark mode you should hear a short bark, in chime mode, you will hear a ding dong, and in alarm mode, you should hear a beep. The alarm will then be set up in about 60 seconds with a short beep. The Main Unit is now ready to protect your selected area.
Test the alarm by walking through the area to be protected. Use the Sensitivity Adjustment to set the desired range of the Main Unit and the Volume Adjustment to set the desired sound level.
IN BARK MODE:
When motion is detected it will cause the alarm to trigger. You will hear a short bark and another if detection continues twice in five seconds. The Main Unit will continue barking for about ten seconds with more than two motion detections within five seconds. If detection continues, or there is a trigger from an add-on sensor, Barking will be at its most vicious (see part Two of this article for setting up add-on sensors). Barking will continue for ten seconds after motion is no longer detected.
IN CHIME MODE:
There will be a ding dong sound for each motion trigger, or add on sensor motion detection.
IN ALARM MODE:
The Main Unit will sound a 3 second siren alarm when it detects one trigger in 5 seconds. If there are two detections within five seconds, the alarm will sound for 6 seconds. If detection continues, or there is a trigger from an add-on sensor (see part Two of this article for setting up add-on sensors), the alarm will continue to sound and reset 20 seconds after motion is no longer detected.
TO DISARM THE SYSTEM:
Press the ARM/DISARM button on the Main Unit, or press the DISARM button once on the Remote Control. The arm LED will go out and there should be a short beep.
THE REMOTE CONTROL PANIC BUTTON:
The Panic Button on the Remote Control will sound a siren alarm for 20 seconds when pressed.
THE MAIN UNIT LOW BATTERY INDICATOR:
When the unit is plugged into home power and the Power/Battery low LED glows amber, it is time to change to a new set of AA Backup Batteries. Failure to do so may cause false triggers of the alarm Main Unit or failure of the alarm to detect if there is a power loss.